Danh mục thiết bị Magtrol 09-09-2026

ListCode 1 

1. Magtrol – Model: 224-212-011 – LMU 212/011

LOAD MONITORING UNIT /2 LEV

Load monitoring unit with 2 sensor input,

2 O/P 4-20 mA and 2 O/P 0-10 V

Power supply 18…32 VDC

2. Magtrol – P/N: 006249

Model:  AHB-12

BRAKE, AIR COOLED, 24V

Rated torque 12 Nm

Max braking power 2,800 W

Max speed 12,000 rpm

24 Volt Coil

This unit requires 620 KPa (90 psi) @ 20 SCFM for proper cooling

3. Magtrol – P/N: 005676

Model:   AHB-1

BRAKE, AIR COOLED, 24V

Rated torque 1.0 Nm

Max braking power 1,200 W

Max speed 25,000 rpm

24 Volt Coil

This unit requires 620 KPa (90 psi) @ 20 SCFM for proper cooling

4. Magtrol – P/N: 007714

Model:   HD-715-5C2-0100

DYNAMOMETER, 240 VAC, 60 PPR, SHORT

Rated torque 6.20 Nm (0-5 Vdc output)

New connectors

Short Base Plate

Max braking power 3,400 W

Max speed 25,000 rpm

Blower Cooled

Encoder 60 PPR

5.Magtrol – P/N: 007714

Model:   HD-715-5C2-0100

DYNAMOMETER, 240 VAC, 60 PPR, SHORT

Rated torque 6.20 Nm (0-5 Vdc output)

New connectors

Short Base Plate

Max braking power 3,400 W

Max speed 25,000 rpm

Blower Cooled

Encoder 60 PPR

6. Magtrol – P/N: 88M370-0500

Model:   CABLE ASSY,M12-4F/CINCH 2M,5m

BRAKE CABLE, M12-4F TO CINCH-2M

*Note: Cable set for use with an existing DSP7000 series controller”

7.  Magtrol – P/N:  88M372-0500

Model:   CABLE ASSY, D-SUB 15F/14P AMPHENOL, 5m

SIGNAL CABLE, D-SUB 15F TO MICRO-RIBBON-14

*Note: Cable set for use with an existing DSP7000 series controller”

8. Magtrol – Model: 843-102-000-011

CTS 102 COGGING TEST SYSTEM 200mNm

Cogging Test System

Measuring range: 0 – 200 mNm

Accuracy: 0.05% of rated torque

Speed: 1 – 10 rpm

Shaft height: 100 mm

Mounted on PT-25 base, length 600 mm

With USB interface

Incl. Control and Data Acquisition Software (LabVIEW exe)”

9.  Magtrol – Model:  424-102-000-211

TS 102/211  0.2Nm 5000PPR

Torque Sensor with smooth shaft

Analog and USB outputs

Rated Torque 0.2 Nm, Accuracy <0.05%

Max Measurable Torque 0.4 Nm

Max speed 1000 rpm

With 5000 Bits Encoder (A, B, Z)

Incl. 3 m. analog and 2 m. USB cables”

10. Magtrol – Model:  843-105-000-011

CTS 105 COGGING TEST SYSTEM 2Nm

Cogging Test System

Measuring range: 0 – 2Nm

Accuracy: 0.05% of rated torque

Speed: 1 – 10RPM

Shaft height: 180mm

Mounted on PT-25 base, length 800 mm

With USB interface

Incl. control and data acquisition software (LabVIEW exe)”

11.  Magtrol – Model:  424-105-000-211

TS 105/211  2Nm 5000PPR

Torque Sensor with smooth shaft

Analog and USB outputs

Rated Torque 2 Nm, Accuracy <0.05%

Max Measurable Torque 4 Nm

Max speed 1000 rpm

With 5000 Bits Encoder (A, B, Z)

Incl. 3 m. analog and 2 m. USB cables”

12.Magtrol – P/N: 317-101-900-021

Model: 1WB32

EDDY CURRENT SYSTEM, WITH FIXTURE, 0.4 Nm

1WB32 High Speed Eddy Current Dynamometer

Rated torque 0.4  Nm at 11,950 rpm

Power rating:  500 W

Maximum speed 80,000 rpm

With integrated Torque-Speed measurement

With integrated dyno excitation suppy

Mounted on 765mm T-Slots base plate

With AMF-1 motor fixture

with protection guard including closing contact

As per drawing 317-101-000V011″

13.  Magtrol -P/N: 88M368-0500

CABLE, D-SUB 15M/D-SUB 15F, 5.0m, SHIELDED

SIGNAL CABLE, D-SUB 15M TO D-SUB 15F, SPECIAL

14. Magtrol – P/N: 957-18-25-0301

EXCITATION CABLE L=5m FOR WB 32 + DSP701X”

15. Magtrol – P/N: 007941

Model: DSP7011

CONTROLLER, 1-CHANNEL (GPIB, USB, 1 I/O)

High-Speed Programmable Dynamometer

Controller, Single Channel, USB Interface,

GPIB Interface, Single I/O Card